Aron Alpha 200Z Series
Aron Alpha 200Z Series is engineered for tough-to-bond situations. Ultra fast setting formula excellent for challenging low surface energy substrates.

Unit of Measure

Specifications

Series

N/A 200Z

Type

N/A 212Z

Unit Size

N/A 20 gm bottle

Units per case

N/A 25

Color

N/A Clear

Gap Fill

N/A 0.006"

Viscosity

N/A 100 cps

Tensile Shear Strength (Steel)

N/A 4600 psi

Temperature Range

N/A -65 ºF to +180 ºF

Set Time (Steel)

N/A 10 s

Bonding Strength to Metal

N/A Excellent

Bonding Strength to Electroplating

N/A Good

Bonding Strength to Rubber

N/A Excellent

Bonding Strength to Plastic

N/A Excellent

Bonding Strength to Hard-Bonding Material

N/A Good

Set Time(PVC)

N/A 5 s

Set Time (ABS)

N/A 5 s

Set Time (Polycarbonate)

N/A 5 s

Set Time (Chroloprene)

N/A 1 s

Set Time (EPDM)

N/A 1 s

Set Time (Steel)

N/A 30 s

Set Time (Aluminum)

N/A 15 s

Tensile Strength (PVC)

N/A 35 N/mm²

Tensile Strength (ABS)

N/A 25 N/mm²

Tensile Strength (Iron)

N/A 32 N/mm²

Tensile Strength (Aluminum)

N/A 25 N/mm²

Tensile Shearing Strength (Polycarbonate)

N/A 7 N/mm²

Tensile Shearing Strength (Chroloprene)

N/A 0.6 N/mm²

Tensile Shearing Strength (EPDM)

N/A 0.6

Form of Packing (20g)

N/A Good

Form of Packing (50g)

N/A Good

Form of Packing (500g)

N/A Good

Tensile Strength

N/A 0.5 x 0.5 x 1.5 inch; bonded area 0.25 sq. inch

Tensile Shear Strength (for plastic and rubber)

N/A 0.1 x 1.0 x 4.0 inch; bonded area 0.5 sq.inch

Tensile Shear Strength (for metal)

N/A 0.064 x 1.0 x 4.0 inch; bonded area 0.5 sq. inch

Bonding Atmosphere

N/A 22 to 24 ºC72 to 75 ºF

Relative Humidity

N/A 58-62%

Testing Methods

N/A ASTM D2095, D3164, and D1002

Before Curing

Appearance (Liquid State)

N/A Colorless and Transparent

Base Monomer (Liquid State)

N/A Ethyl 2-Cyanoacrylate

Viscosity (Liquid State)

N/A 85 cps

Specific Gravity (d20)-(Liquid State)

N/A 1.05

Flash Point (Closed Cup)-(Liquid State)

N/A 83 ºC181 ºF

Freezing Point (Liquid State)

N/A -29 ºC-20 ºF

After Curing

Appearance (Solid State)

N/A Colorless and Transparent

Specific Gravity (d20)-(Solid State)

N/A 1.25

Hardness (Rockwell M)-(Solid State)

N/A 85

Softening Point (Vicat)-(Solid State)

N/A 145 ºC293 ºF

Storage

N/A

  • Store product in the unopened container in a dry location.

Humidity

  • Avoid moist, humid storage conditions.
  • Fasten cap tightly to avoid exposure to moisture.
  • Store with desiccant.

Temperature

  • Avoid storing at a

Warning

N/A

  • May have an irritating odor, Aron Alpha might irritate eyes, nose and throat. Please maintain proper ventilation it is used in large amounts or for a long period of time. Please wear protective glasses and/or hood shield.
  • In case of absorbing into cloth, Aron Alpha will rapidly polymerize and result in heating. During operation, avoid wearing gloves made of absorbable materials, instead use solvent proof polyethylene gloves.
  • ARON ALPHA is a flammable liquid. Use in a well ventilated area, and keep away from fire.
  • Eye and Skin irritant. Bonds skin instantly. Combustible - keep away from heat and flames.

Features

N/A

  • Ultra fast setting for bonding difficult-to-bond materials such as soft PVC, Polycarbonate, ABS, etc.
  • Low and medium viscosity grades.

Characteristics of Aron Alpha® Cyanoacrylate Adhesives

Characteristics

N/A
  • Instant Bonding :
    Adhesion is achieved in a few seconds, It is well suited for increasing the efficiency of the manufacturing process.
  • Easy to use:
    Adhesive is single component and heat treatment are not required. Perfect f

Method of Disposal

N/A

  • Expose the adhesives in the containers to moisture and light to let it harden slowly, and to treat it as waste plastics (drastic hardening may result in heating, pay attention to this situation).
  • Please comply with local regulations when dispos

Precaution

N/A

When in contact with Skin

  • Don't peel it off forcibly, instead use warm water or remover to rub it off.

When in contact with Eyes

  • It will damage the eyes to rub the eyes or to use solvents. Must rinse with large amount of water and get medical attention.

Setting Time

N/A

(in seconds for various materials)

Material Setting Time (sec)
(Substrate material bonded to substrate material) 212Z
PVC (Rigid)/PVC 10
PMMA (Polymethylmetacrylate)/PMMA 3
ABS (Acrylonitrile butadiene styrene)/ABS 5
PC (Polycarbonate)/PC 5
Natural Rubber/Natural Rubber 10
Steel/Steel 5
Copper/Copper 5
Phenolic Resin/Phenolic Resin 5
Rigid PVC/Steel 5
Aluminum/ABS 5
Stainless Steel/FRP 15
Neoprene Rubber/Steel 5
Neoprene Rubber/ABS 5

Bonding Strength (Tensile)

N/A

(Tensile measured in psi for various materials)

Material Tensile Strengths (psi)
(Substrate material bonded to substrate material) 212Z
PVC (Rigid)/PVC 5000
PMMA (Polymethylmetacrylate)/PMMA 5000
ABS (Acrylonitrile butadiene styrene)/ABS 3600
PC (Polycarbonate)/PC 5000
Natural Rubber/Natural Rubber 2800
Steel/Steel 4600
Copper/Copper 2800
Phenolic Resin/Phenolic Resin 4100
Rigid PVC/Steel 2600
Aluminum/ABS 2100
Stainless Steel/FRP 3800
Neoprene Rubber/Steel 360
Neoprene Rubber/ABS 360

Bonding Strength (Shear)

N/A

(Shear measured in psi for various materials)

Material Shear Strengths (psi)
(Substrate material bonded to substrate material) 212Z
PVC (Rigid)/PVC 1400
PMMA (Polymethylmetacrylate)/PMMA 710
ABS (Acrylonitrile butadiene styrene)/ABS 710
PC (Polycarbonate)/PC 1000
Natural Rubber/Natural Rubber 570
Steel/Steel 2800
Copper/Copper 2300
Phenolic Resin/Phenolic Resin 2600
Rigid PVC/Steel 1400
Aluminum/ABS 1000
Stainless Steel/FRP 2300
Neoprene Rubber/Steel 57
Neoprene Rubber/ABS 57

Applications

N/A

  • For Wood Work: Suitable for bonding wood. Complete and wide range of adhesive grades available. Suitable for assembling wooden products and repairing. Wooden molds and expensive rare woods.
  • Artificial Marble: For use on artificial marble with various kinds of colors such as transparent, white, black and grey.
  • Color Grades: Able to confirm the coating colors of adhesives.
  • Remover: For use in removing hardened substances and peel off parts of adhesives